HP Pavilion Slimline s3000 Desktop PC series support
Installing or Replacing a Hard Drive
This document provides step-by-step instructions and links to a video on how to remove and add an IDE hard drive on HP and Compaq desktop computers. The document also provides instructions for replacing an IDE drive with a Serial ATA (SATA) drive.
It might help to print this article for easy reference before starting the hardware change.
NOTE:HP cannot be held liable for damage resulting from improper installation of software and/or parts, or the installation of parts and/or software that were not supplied by HP.
NOTE:The images in this document might not be exactly the same as the computer you are using.
Before you begin
Before you begin, check the following items:
- If installing an additional drive, make sure that your computer has at least one additional drive bay. Many HP and Compaq desktop computers only have one drive bay and it is already in use. For these computers the only option is to upgrade the hard drive.
- Make sure the motherboard in the computer can support the type of drive that you want to install. The most compatible drives are IDE, followed by Ultra-IDE (EIDE), and then Serial ATA (SATA).
- If you want to add an additional hard drive to the computer, you probably should upgrade the power supply as well. Especially if additional components like memory or a CD or DVD drive were also added.
- If adding an IDE drive to a computer that already contains an IDE hard drive, you might need an IDE cable that has three connectors. Some HP and Compaq computers use IDE cables that contain only two connectors, one for the motherboard connection and one for the back of one drive.
- If you are replacing an IDE drive with a Serial ATA (SATA) drive, you might need a PCI SATA controller card or a SATA to IDE adapter.
- If you are replacing a drive, get a recovery disc set for your exact model of computer.
- If you are installing new drive, you will need recovery discs to format the new hard drive.
- Get a Phillips screwdriver and a medium flat-blade screwdriver.
- HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the computer.
- Find a clear, flat, stable work surface over a non-carpeted floor.
Installation overview video
This video is provided as a supplement to the instructions in this document to gain a familiarity with what can be involved in performing this procedure. Read the other sections before attempting to add or replace hardware.
NOTE:Your case will probably be different than the case example used in the video.
NOTE:For best quality on dial-up connections, wait until the video has fully loaded before viewing.
View by clicking the Play control under the video screen. |
Click the Pause control to stop the video.
Go to the beginning of the video by clicking the Rewind control.
Silence or enable audio by clicking the Audio control. (Audio in English)
Step 1: Opening the case
Use the following steps to open the case:
WARNING:The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the computer.
CAUTION:This product contains components that can be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected to a grounded surface.
- Unplug all cables except for the power. Write down each cable location if you do not already know where it connects.
- Unplug the power cable and with the power cable removed press the Power button on the front of the computer.
- Remove the screws on the rear of the computer.
- Slide both side panels off from the rear of the computer.
- On some cases, it might be necessary to remove the front of the computer so that you can remove the drive cage. If so, press in on the tabs that retain the front cover, there should three to four on each side of the cover and gently pull forward. It helps to have a friend help with this process. Carefully detach any cables that are also attached to the front cover.
Step 2: Disconnecting the cables
- If you are replacing a drive, use this section to find and unplug the IDE/Serial ATA or power cables.
- If you are adding an additional drive and the empty bay is part of a removable drive cage, use this section to find and unplug the cable to make the drive cage removal easier.
- If you are adding an additional drive into an empty drive bay on the chassis, skip this section and go to Step 5 .
- Find the hard drive. The hard drive usually sits under the CD and DVD drives and has a thin flat ribbon cable.
- Disconnect the IDE or Serial ATA cable and the power cable from the back of the drive. remember where each cable goes.
Step 3: Removing the drive cage
On many HP and Compaq computers, drives are attached to drive cages. Often, the installation and removal instruction for the cages are located next to the drive cage or on the side panel. The following images are some examples of the types of drive cages that come on HP and Compaq computers. For more detailed information about a particular chassis, refer to the Hardware and Servicing guide or User Guide for your particular model of computer.
CAUTION:Many Media Center computers come with a swing out drive bay (shown below). The plastic covering for the memory card reader must be removed and the cord to the front panel lights must be unplugged before the drive bay can be removed.
Step 4: Removing the drive
- If the drive is attached to the chassis or drive cage with screws, remove the screws and slide the drive out.
- If the drive is retained by a plastic latching system, lift the latch to slide the drive out.Set the old drive aside. If the drive is to be re-used, place it in an ESD safe container for storage.
Step 5: Installing a new drive
Use the following steps to install a new hard drive into the computer:
- If you are installing an IDE hard drive, Make sure the jumpers on the drive are set to Cable Select or CS.Not sure which pins represent Cable Select? Refer to the labeling on the drive itself, looking for CS. If the drive is not labeled, refer to drive documentation.NOTE:Serial ATA drives do not require jumpers.
- Slide the new drive into the open bay until the screw holes align with the holes in the chassis or drive cage. If the drive attaches to the chassis using a plastic latch you will need to insert the screws into the drive and screw them down before sliding the drive into place.
- If a drive cage was removed, reattach the drive cage and secure it in place.
- Connect the cables, following the instructions for the type of drive you are installing.If you are installing a Serial ATA drive, connect the Serial ATA cable into the first open SATA slot on the motherboard, SATA1 first or SATA2 second. Connect the other end of the Serial ATA cable into the back of the hard drive.If you are installing a Serial ATA drive as a replacement for an IDE drive, check the motherboard for an open SATA slot. If the motherboard does not have an open SATA slot, you can purchase and install a PCI SATA controller card or a SATA to IDE adapter.If using a PCI SATA controller card, connect the Serial ATA cable from the drive to a SATA slot on the controller card.If using a SATA to IDE adapter, follow the instructions for the adapter.If you are installing a IDE drive, connect the end of the IDE cable into the IDE interface connector on the back of the drive as follows:NOTE:If the motherboard and hard drives are capable of Ultra-IDE, make sure that use an Ultra-IDE cable. A regular IDE cable will work, but the data transfer rates will not be as good.If the IDE cable was removed from the motherboard, connect the other end of the IDE cable into the motherboard (into the Primary IDE slot). This can be difficult because space is limited. Be very careful to not dislodge the other cables and make sure that it fits snugly into its connector. Use a flashlight to make this easier.
- Connect the power cable into the back of the drive. Be careful to not dislocate any other cables.
- Make sure that all of the connectors are fully seated. A loose cable can cause many different types of boot errors.
Step 6: Replacing the cover(s)
- If the front cover was removed earlier, connect any cables that go to the front cover, align the tabs on the front cover to the holes in the front of the chassis and snap the front cover into place.
- Replace a side panel by matching the side panel tabs with the tab openings in the case.
- Insert the side panel and slide it forward.
- Fasten the screws to secure the side panel. Repeat for the other panel.CAUTION:MBR or NTFS partitions are limited to 2 TB (without using dynamic disks and volume sets). If you are installing a hard drive that is 2 TB or greater, HP recommends formatting the drive using GPT partitions.
Step 7: Configuring the new hard drive in the BIOS
Finding the BIOS version on your computer
The procedure for configuring the hard drive depends upon the BIOS version on your computer. Follow these steps to determine the BIOS version on your computer. Then proceed to the section that matches the BIOS version on your computer.
NOTE:If your computer was built before 2006 (came with Windows XP or earlier), then it has BIOS version 6 or less. Go to Configuring the hard drive in BIOS version 6 or less .
- Turn on the computer.
- If your computer was built in 2006 or later (Windows 7 or Vista), immediately press the F10 key. You might need to press the key repeatedly, about once every second, until a BIOS Setup utility screen opens.
- If your computer was built before 2006 (Windows XP or earlier), immediately press the F1 key. Your computer has BIOS version 6 or less. Go to Configuring the hard drive in BIOS version 6 or less .
- In the BIOS Setup utility, do one of the following:
If your computer has BIOS version 7 or greater, go to Configuring the hard drive in BIOS version 7 or greater .
- On the Main tab, find the BIOS version.If your computer has BIOS version 6 or less, go to Configuring the hard drive in BIOS version 6 or less .
- Turn on the computer.
- If your computer was built before 2006 (Windows XP or earlier), immediately press the F1 key. You might need to press the key repeatedly, about once every second, until a BIOS Setup utility screen opens.
- On the Main tab, make sure the new drive shows up under its proper location (1st or 2nd drive or First or Second Channel Device). If not, exit BIOS, turn off the computer, open the case and make sure the IDE and power cables are firmly and correctly connected. Once the settings are confirmed, close the case and repeat step 1.
- If you are installing a hard drive that already contains data you are done with installation. Restart the computer to begin using it.
- If you are adding a blank hard drive, continue with the next step.
- If the hard drive is replacing the primary hard drive, insert the first recovery disc or a startup disc into the optical drive, restart the computer, and follow the instructions that appear to recover the computer.If a second hard drive was added, use the following steps depending on the versions of Windows you have:
If the disk does not show up in Windows with usable space, use the following steps to format the drive and make it usable:
- Click Start , then click Computer .If the new drive displays with usable space, you are done.If the new drive is not displayed or shows no usable space, continue with the next step to format the drive.
- Click Start , right-click My Computer , and select Manage .
- Under Storage, select Disk Management .
- Right click the new drive and then click Format .
- Follow the on-screen instructions.
- In Windows XP, click Start , right-click My Computer , and select Manage .
- Select Disk Management from the left side.
- Right click the icon from the new drive in the right side and select Format .
- Follow the on-screen instructions.
- Turn on the computer and immediately press the F10 key. You might need to press the key repeatedly, about once every second, until a BIOS Setup utility screen opens.
- Press the right arrow key to open the Storage tab.
- Press the down arrow key, select Device Configuration , and then press Enter .
- Make sure the hard drive displays in the Device Configuration window.
- If you are adding a blank hard drive, continue with the next step.
- If the hard drive is replacing the primary hard drive, insert the first recovery disc or a startup disc into the optical drive, restart the computer, and follow the instructions that appear to recover the computer.If a second hard drive was added, use the following steps:Click Start , then click Computer .If the new drive displays with usable space, you are done.Click Start , right-click My Computer , and select Manage .Under Storage, select Disk Management .Right click the new drive and then click Format .Follow the on-screen instructions.
Step 8: Setting up RAID configuration
If a RAID (Redundant Array of Independent Disks) manager is installed on the computer and you have two or more hard drives installed, you can set up RAID configuration. RAID technology allows several hard disk drives to function as one storage area (the array) to provide either data redundancy (a copy of a hard drive for backup security) or faster performance (striped reading/writing data from or to the disk drives to create one larger drive).
To find the RAID manager installed on your computer, click Start , All Programs , then look for one of the following:
You have the Intel Matrix Storage Console. See one of the following HP Support documents for more information about setting up a RAID configuration on your computer:
If you have a folder named AMD under All Programs, then you have AMD RAIDXpert Storage Technology. For more information about setting up a RAID configuration on your computer, see Setting Up RAID Using AMD RAIDXpert Storage Technology .
If you have a folder named NVIDIA Corporation under All Programs, then you have NVIDIA RAID Utility. For more information about setting up a RAID configuration on your computer, see Using NVIDIA RAID Utility for Windows Vista .
You have NVIDIA MediaShield. For more information about setting up a RAID configuration on your computer, see Setting Up RAID Configuration Using NVIDIA MediaShield .
You have Promise Array Management on your computer. For more information about setting up a RAID configuration on your computer, see Setting Up and Troubleshooting RAID Configuration Using Promise Array Management .
Troubleshooting a hard drive installation
If you experience problems after installing a new hard drive, see the HP Support document, Troubleshooting a New Hard Drive Installation .