HP Pavilion a4000 Desktop PC series support
Printer Specifications for HP LaserJet P1006 and P1009 Printers
Review the following sections for product-specific information.
HP LaserJet P1006 and P1009 models
|Printer model||Part number|
|HP LaserJet P1006 Printer||CB411A|
|HP LaserJet P1009 Printer||CC444A|
|Connectivity||Hi-Speed 2.0 USB port.|
|Base memory||8 MB RAM|
|Width||349 mm (13.7 inches)|
|Depth||Depth: 238 mm (9.4 inches)|
|Height||195 mm (7.7 inches)|
|Weight (cartridge installed)||5.2 kg (11.5)|
To purchase cartridges or check cartridge compatibility for your printer, go to HP Home & Home Office Store (US only), and then click Ink Toner & Paper.
If you are located outside of the US, follow these steps to purchase cartridges using HP SureSupply.
- Go to HP SureSupply .
- Scroll to the bottom of the page and make sure that the country/region location is correct.
Genuine HP cartridges can also be purchased from other retailers.
The following tables contain specifications for supported paper.
Paper tray capacities
|Main input tray capacity||150 sheets of regular weight 75 g/m22 (20-lb paper )|
|Priority feed slot capacity||10 sheets of paper up to 163 g/m22 (43 lb)|
|Top (face down) output bin capacity||100 sheets of regular weight 75 g/m22 (20 lb) paper|
|Output bin||60 to 105 g/m22 (16 lbs to 28 lbs )|
Paper types and sizes
|Letter||216 x 279 mm (8.5 x 11 inches)|
|Legal||216 x 355.6 mm (8.5 x 14 inches)|
|Executive||184 x 267 mm (7.24 x 10.51 inches)|
|A4||210 x 297 mm (8.27 x 11.69 inches)|
|A5||148 x 210 mm (5.83 x 8.27 inches)|
|A6||105 x 148 mm (4.13 x 5.83 inches)|
|B5 (JIS)||182 x 257 mm (7.17 x 10.12 inches)|
|Envelope #10||105 x 241 mm (4.13 x 9.49 inches)|
|Envelope DL||110 x 220 mm (4.33 x 8.66 inches)|
|Envelope C5||162 x 229 mm (6.93 x 9.84 inches)|
|Envelope B5||176 x 250 mm (6.93 x 9.84 inches)|
|Envelope Monarch||98 x 191 mm (3.86 x 7.52 inches)|
|16K||197 x 273 mm (7.75 x 10.75 inches)|
195 x 270 mm (7.68 x 10.63 inches)
184 x 260 mm (7.24 x 10.24 inches)
|8.5 x 13||216 x 330 mm (8.5 x 13 inches)|
|B5 (ISO)||176 x 250 mm (6.93 x 9.84 inches)|
|Post memory card||100 x 148 mm (3.94 x 5.83 inches)|
|Double Post memory card||148 x 200 mm (5.83 x 7.87 inches)|
NOTE:Narrow and heavy paper can cause the product to print more slowly.
WARNING:Power requirements are based on the country/region where the printer is sold. Do not convert operating voltages. Doing so might damage the product and void the product warranty.
|Model voltage||Power requirements||Rated current|
50/60 Hz (+/-2 Hz)
50/60 Hz (+/-2 Hz)
|Power mode||Power use|
1 Power reported is highest values measured for monochrome printing using all standard voltages.
2 The default time from Ready mode to PowerSave mode and the recovery time from PowerSave mode to the start of printing is negligible (less than 10 seconds) because of the instant-on fusing.
Maximum heat dissipation for all models in Ready Mode = 62 BTU/Hour.
The following information contains the environmental specifications for the product.
Recommended operating conditions
|Temperature||17.5°C to 25°C (63.5°F to 77° F)||10°C to 32.5°C (50°F to 90.5° F)||0°C to 40°C (32°F to 104°F)|
|Relative Humidity||30% to 70% (no condensation)||10% to 90% (no condensation)||10% to 90% (no condensation)|
|Sound power level||Declared per ISO 9296|
|Printing (14 PPM)||LWAd = 6.29 Bels (A) [63 dB (A)]|
|Sound pressure level bystander position||Declared Per ISO 9296|
|Printing (14 PPM)||LWAd = 50 dB(A)|
Configuration tested: HP LaserJet P1006 printer, continuous monochrome printing on A4 paper at 16 PPM.
The following information contains the regulatory specifications for the product.
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instructions, it might cause harmful interference to radio communications. However, there is no guarantee that interference does not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase separation between equipment and receiver.
- Connect equipment to an outlet on a circuit different from that to which the receiver is located.
- Consult your dealer or an experienced radio/TV technician.
NOTE:Any changes or modifications to the product that are not expressly approved by Hewlett-Packard could void the authority to operate this equipment.Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules.